This is my first attempt of compiling something in the Arduino environment, so a lot of obvious things aren't that obvious to me.
So after hopefully installing all the right libraries, I get a lot of errors of the kind shown below:
C:\Program Files\WindowsApps\ArduinoLLC.ArduinoIDE_1.8.55.0_x86__mdqgnx93n4wtt\libraries\Adafruit_Circuit_Playground\Adafruit_CircuitPlayground.cpp: In member function 'void Adafruit_CircuitPlayground::playTone(uint16_t, uint16_t, bool)':
C:\Program Files\WindowsApps\ArduinoLLC.ArduinoIDE_1.8.55.0_x86__mdqgnx93n4wtt\libraries\Adafruit_Circuit_Playground\Adafruit_CircuitPlayground.cpp:238:3: error: 'PLLFRQ' was not declared in this scope
PLLFRQ = (PLLFRQ & 0xCF) | 0x30; // Route PLL to async clk
^~~~~~
C:\Program Files\WindowsApps\ArduinoLLC.ArduinoIDE_1.8.55.0_x86__mdqgnx93n4wtt\libraries\Adafruit_Circuit_Playground\Adafruit_CircuitPlayground.cpp:238:3: note: suggested alternative: 'PCIFR'
PLLFRQ = (PLLFRQ & 0xCF) | 0x30; // Route PLL to async clk
^~~~~~
PCIFR
C:\Program Files\WindowsApps\ArduinoLLC.ArduinoIDE_1.8.55.0_x86__mdqgnx93n4wtt\libraries\Adafruit_Circuit_Playground\Adafruit_CircuitPlayground.cpp:239:3: error: 'TCCR4A' was not declared in this scope
TCCR4A = _BV(COM4A0) | _BV(PWM4A); // Clear on match, PWMA on
^~~~~~
C:\Program Files\WindowsApps\ArduinoLLC.ArduinoIDE_1.8.55.0_x86__mdqgnx93n4wtt\libraries\Adafruit_Circuit_Playground\Adafruit_CircuitPlayground.cpp:239:3: note: suggested alternative: 'TCCR0A'
TCCR4A = _BV(COM4A0) | _BV(PWM4A); // Clear on match, PWMA on
^~~~~~
TCCR0A
In file included from c:\program files\windowsapps\arduinollc.arduinoide_1.8.55.0_x86__mdqgnx93n4wtt\hardware\tools\avr\avr\include\avr\io.h:99:0,
from c:\program files\windowsapps\arduinollc.arduinoide_1.8.55.0_x86__mdqgnx93n4wtt\hardware\tools\avr\avr\include\avr\pgmspace.h:90,
from C:\Program Files\WindowsApps\ArduinoLLC.ArduinoIDE_1.8.55.0_x86__mdqgnx93n4wtt\hardware\arduino\avr\cores\arduino/Arduino.h:28,
from C:\Program Files\WindowsApps\ArduinoLLC.ArduinoIDE_1.8.55.0_x86__mdqgnx93n4wtt\libraries\Adafruit_Circuit_Playground/utility/Adafruit_CPlay_LIS3DH.h:30,
from C:\Program Files\WindowsApps\ArduinoLLC.ArduinoIDE_1.8.55.0_x86__mdqgnx93n4wtt\libraries\Adafruit_Circuit_Playground/Adafruit_Circuit_Playground.h:21,
from C:\Program Files\WindowsApps\ArduinoLLC.ArduinoIDE_1.8.55.0_x86__mdqgnx93n4wtt\libraries\Adafruit_Circuit_Playground\Adafruit_CircuitPlayground.cpp:30:
...
...
exit status 1
Error compiling for board Arduino Uno.Any ideas would be highly appreciated.
Cheers,
-max
Yes, you could try the "m" command.
m index angle
for example,
m8 -10
m12 30
Make sure you set the serial monitor as "no line ending" and baudrate 115200 before entering "y" for the WriteInstinct.ino for correct parsing.
Thanks, I finally got it working. Re-did all the calibration steps and then everything started to work.
Now I'll have to understand better on how I can add my own 'tricks' to it.
Thanks for all the patient help
But that's what I did. Calibrate the servos without the legs on, the attach the legs as square as possible. But as soon as I switch the board on, hold the dog in the air and press a button on the remote (no idea really which one I should or should not) and the thing goes berserk. Unfortunately, I'm not learning anything here as I have no idea what I'm actually doing or trying to do. It's all a black box at this point.
Is there a command where I could at least instruct a particular servo to rotate by some amount? This way I at least would be able to check if I wired up everything correctly.
It would also help to know what all the different buttons on the remote are for. Is there a diagram/picture I can find?
I then attached the legs and set them to the angle as an indication.
These steps are done in the wrong order. You need to connect the servos to the board, send the calibration signal to make them to calibration position, then attach the legs.
The logic behind the calibration process.
You are getting close to a complete setup. Every time you find something that doesn't work up to your expectation, you learn something new and deeper to nature.
I'm close to giving up here. I uploaded the code, ran the calibration step, including the servo calibration. i then attached the legs and set them to the angle as indication. But then when I switched it on and pressed a button on the remote control (there is no '1' button on my remote control) the servos go berserk, they very quickly move around, the front leg ripped off the head and fortunately I could switch off power quickly.
I have no idea what I'm doing here, flying completely blind. Really frustrating.
Any idea how I can troubleshoot this.