Error Compiling Instinct
I am able to load, compile and load TestBuzzer and it works. When I try to compile the WriteInstinct I get an error: exit status 1
Error compiling for board ATmega328P (5V, 20 MHz) NyBoard V0_1. I verified that Instinct.H shows NyBoard_V0_1 which is the board I have. The compile stops 3 seconds after starting.
103 Views
Continuo a ricevere iseguenti errori e non riesco ad andare avanti per favore qualcuno puo' aiutarmi ?
In file included from C:\Users\Sergio\AppData\Local\Temp\arduino_build_995809\sketch\OpenCat.h:85:0, from C:\Users\Sergio\Documents\Arduino\libraries\OpenCat\WriteInstinct\WriteInstinct.ino:31: C:\Users\Sergio\AppData\Local\Arduino15\packages\arduino\hardware\avr\1.8.3\libraries\Wire\src/Wire.h: In member function 'void Motion::loadDataFromI2cEeprom(unsigned int&)': C:\Users\Sergio\AppData\Local\Arduino15\packages\arduino\hardware\avr\1.8.3\libraries\Wire\src/Wire.h:68:13: note: candidate 1: uint8_t TwoWire::requestFrom(int, int) uint8_t requestFrom(int, int); ^~~~~~~~~~~ C:\Users\Sergio\AppData\Local\Arduino15\packages\arduino\hardware\avr\1.8.3\libraries\Wire\src/Wire.h:65:13: note: candidate 2: uint8_t TwoWire::requestFrom(uint8_t, uint8_t) uint8_t requestFrom(uint8_t, uint8_t); ^~~~~~~~~~~alla fine della compilazione pare che tutto venga trasferito ma credo ci sia ancora una ulteriore segnalazione del compilatore :
avrdude: Version 6.3-20190619 Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/ Copyright (c) 2007-2014 Joerg Wunsch System wide configuration file is "C:\Users\Sergio\AppData\Local\Arduino15\packages\arduino\tools\avrdude\6.3.0-arduino17/etc/avrdude.conf" Using Port : COM13 Using Programmer : arduino Overriding Baud Rate : 115200 AVR Part : ATmega328P Chip Erase delay : 9000 us PAGEL : PD7 BS2 : PC2 RESET disposition : dedicated RETRY pulse : SCK serial program mode : yes parallel program mode : yes Timeout : 200 StabDelay : 100 CmdexeDelay : 25 SyncLoops : 32 ByteDelay : 0 PollIndex : 3 PollValue : 0x53 Memory Detail : Block Poll Page Polled Memory Type Mode Delay Size Indx Paged Size Size #Pages MinW MaxW ReadBack ----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ----- --------- eeprom 65 20 4 0 no 1024 4 0 3600 3600 0xff 0xff flash 65 6 128 0 yes 32768 128 256 4500 4500 0xff 0xff lfuse 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00 hfuse 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00 efuse 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00 lock 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00 calibration 0 0 0 0 no 1 0 0 0 0 0x00 0x00 signature 0 0 0 0 no 3 0 0 0 0 0x00 0x00 Programmer Type : Arduino Description : Arduino Hardware Version: 3 Firmware Version: 4.4 Vtarget : 0.3 V Varef : 0.3 V Oscillator : 28.800 kHz SCK period : 3.3 us avrdude: AVR device initialized and ready to accept instructions Reading | ################################################## | 100% 0.00s avrdude: Device signature = 0x1e950f (probably m328p) avrdude: reading input file "C:\Users\Sergio\AppData\Local\Temp\arduino_build_995809/WriteInstinct.ino.hex" avrdude: writing flash (25572 bytes): Writing | ################################################## | 100% 3.99s avrdude: 25572 bytes of flash written avrdude: verifying flash memory against C:\Users\Sergio\AppData\Local\Temp\arduino_build_995809/WriteInstinct.ino.hex: avrdude: load data flash data from input file C:\Users\Sergio\AppData\Local\Temp\arduino_build_995809/WriteInstinct.ino.hex: avrdude: input file C:\Users\Sergio\AppData\Local\Temp\arduino_build_995809/WriteInstinct.ino.hex contains 25572 bytes avrdude: reading on-chip flash data: Reading | avrdude: stk500_paged_load(): (a) protocol error, expect=0x10, resp=0x00 avrdude: stk500_cmd(): programmer is out of sync avr_read(): error reading address 0x0000 read operation not supported for memory "flash" avrdude: failed to read all of flash memory, rc=-2 avrdude: stk500_disable(): protocol error, expect=0x14, resp=0x2a avrdude done. Thank you.Puo' essere che la scheda NyVoard V1_0 sia danneggiata ?